Motorcycle Windshield Reviews

Rider is 6' tall with a 34" inseam

Just test rode with the new windshield, I love it.
I would estimate that there was an ~2" mild area above my helmet before the main force of the wind was felt, 70+mph etc., using my hand and slowly raising it starting at my face.
I even raised my body up, easily well over 2", and did not feel any wind force on my head that was at all annoying, just the normal amount of minor wind, not the main force. Which was actually kind of strange because that 14.5" windshield that I tested and returned seemed too low, I don't remember all the particulars but I returned it so obviously it didn't work for me.
I took a bunch of pictures in a much better area than in the garage, lol. I'm going to go through them really quick and crop or whatever is needed and I will send them to you.
I'm going to want another windshield similar for my other 2003 FXDWG. I've been running a Corbin Dual Tour seat on it for a while, and I also have a Corbin Gunfighter and Lady for it. On the two-tone bike I was just riding, I am running a Corbin Classic Solo that I had made specifically for me at a ride-in appointment in Hollister.
I just purchased another used classic solo seat, and I also have one on my 2003 FXDL Low Rider. One of those is going to go onto the Gunmetal Pearl 2003 bike, and I'm selling the heated dual tour seat that's on it. Once I get that seat figured out I'm going to want to get a shorter windshield from you because the one that's currently on it is OEM. (Pretty good chance that the seat currently on the FXDL is staying there since that one works really well with the short windshield that I purchased from you)
That OEM height on the one that was on this two-tone bike had the top edge right where I didn't want it, and then there was distortion when looking through the shield just below the top and it was right at the most important place for me to see, with my height in the saddle on that bike using that seat. SO much better now!
Best wishes, Jon

I have the medium height with medium grey tint with vent on a Lowrider ST El Diablo. At 5’ 7” I am looking over it most of the time. The wind just hits the top of my helmet at highway speeds. Behind the windshield my shirt has a tendency to float around in the low pressure area. The wind noise and buffeting is greatly reduced and allows more use of the audio system. The bike is definitely more comfortable with the additional height and width.
The tint is slightly lighter than stock ( good since it’s taller and I look through it more often).
The clarity is slightly cloudy compared to stock. Maybe its the tint or lack of coatings but its not bad. Again, I am looking over it most always.
The attachment hardware isn’t as fancy as the HD hardware but isn’t bad.
Clearview made what seemed like a long wait very bearable with good communication and updates. I was impressed.
Overall, I am pleased with the purchase. Its not absolute top quality but its not $500 -$1000 either.

This is my second Clearview Shield I've purchased for my bike. I liked my first one so much, I bought a second one a size larger. Not that there was anything wrong with my first shield, but I wanted a taller one for when it's colder, I have a passenger on the back, or when I'm taking long highway trips with my full face or modular helmet, just to eliminate any buffering at sustained highway speeds. I like that there is no distortion in the recurve, and that the shield doesn't flex and vibrate in the wind. If you're on the fence, just order it. It's worth it.

Ordered May 14th and a well packed windshield arrived June 20th. Was notified via email the production team was running behind. The included instructions are very detailed and the return/warranty policy seem good. I was on the fence between returning the Medium (17 1/2″ vertical) shield and ordering the Large (18 1/2″ vertical) shield. I wanted to essentially eliminate all turbulence. It's a motorcycle though so I don't think this is possible lol. The airstream seams to pass just above my head just touching my helmet. The view over the shield is very good. I think the Large would allow me to look over the shield to the horizon but just barely. I value the view more than reducing the noise by a negligible amount. Road about 600 miles through rain in the past couple days. I would not want to have to look through a wet visor and windshield at the same time. Also, sitting upright and leaning forward allows the air stream to blow the rain off my helmet visor. The 5 position vent does seem to help keep turbulence lower depending on the setting. There is a low pressure zone as I saw water droplets swirling around in the pocket of space between my chest and handlebars. Fit and finish is good aside from some hairline air bubbles on the black backing around the mounting holes. I don't care too much about that. I don't have the chrome strip since I am not the original owner. I used stainless washers to distribute the pressure from the mounting bolts. I like the look of it better too black into black. If you're similar to me 6' 32" Inseam don't get smaller than Medium for wind reduction. Taller than 6'? Large would probably work for you to look over comfortably. Take into account I ordered a recurve option (provides 1.5 – 2″ of lift to the airstream). My photo of the instrument cluster simulates about how far over the top of the shield I can see.

Works great! Fits perfect! Well made! Blocks wind very well! Completely happy with my purchase. Would buy again in a heartbeat!
Also came with hardware which is great!

This windshield rocks! I can't say enough about how happy I am with the new windshield and the service overall was fantastic. It fit great, looks great, and is high quality. I highly recommend this company for your windshield needs.

The 13" windshield fit perfectly on my 2000 Honda Interstate. I'm 5' 11" and I only feel slight buffeting as I near 80 mph. I appreciated the ability to test it with the wrapping on first, just in case I needed to send it back, but I didn't. Perfect fit. Happy customer.
Thank you!

Mounting was relatively easy. Except the hols on the top mount were slightly larger than the screw. The whole was not big enough to use the rubber washers with the inset to mount as per HD. I was able to find a sleeve small enough to fit and uses two washers instead of the one-piece rubber grommets as originally used with HD. Nice to see clean after 130,000 miles. The product looks great! Customer service was outstanding. I liked hearing how happy it made the representative/Owner that I was replacing one with so many miles on it. The lag time was not too bad. It was made in the USA.

Put New wind shield on my 2017 Tri Glide, 2 in. higher then stock. Fit perfect. The rain now goes over my head, instead of right to my face. Was in a hail storm, no marks at all. Great quality

windshield quality and clarity is very good.....Because of the increased size and curve of the screen took a little time to get it aligned with the OEM bracket holes...all in all very satisfied